Abahub 236 mil 16 sqft Car Sound Deadener Hood Firewall Heat Shield Insulation Pad Automotive Sound Deadening Mat Aluminum Roll 59"x39"

Worked well to replace the old insulation eaten by a squirrel who wintered in the hood of the car! Used in a 2010 Chevy Impala. It was easy to trace, cut , and the installation went well. I suggest taking off just the center backing first, and put in those pegs; then take off one side at a time to make,m sure everything is aligned correctly. It's a good product and I highly recommend this!

I used it for sound reduction and rodent deterrent under the hood of my SUV. Worked great. Replacing the wood fiber sound reduction material that was originally installed by the vehicle manufacturer. Easy to install if you make a paper or cardboard template first, then cut the material to match the template, then apply it to the material. Suggest you make a practice run before you peel off the back adhesive protection sheet. You only get one chance to stick this to the surface where you want it, can't pull it off and reapply.

The adhesive is exceptionally good on this heat shield I put it on my sxs plastic which could have probably been cleaner. The heatshield has held up so far and was easy to install. Exactly what I wanted and for a fair price. I Will more than likely purchase more.

My only issue with this product is that it's advertised as a sound deadener but in reality, its more of a heat shield than anything, it does a really good job of blocking the heat but if I knew it wasn't a sound deadener, I would've use the siless sound deadener under it first. I have two trucks I installed this in, my first one is a humvee, I didn't use any of the siless, the heat is reduced by a lot, but the sound is not reduce that much.The second vehicle I use this in is a M35a2 deuce and a half, this time I used siless 80mil and then put this over it in the hot areas and it done a tremendous job on stopping the sound and heatOne thing I would tell you guys, use the siless sound deadener and put this over it, your ride quality would be so much better

This stuff is sticky, almost too sticky. Lol. I used it in a generator box and it does great at getting the sound levels lower.

The thickness was as described. Worked great inside of my 3D printer for sound and heat retention.

Make sure that you have this where you want it before sticking it down. It sticks well, but if you need to pull it off to reposition it, it will rip and leave part of the mat. It does stick very well, so hopefully I will never have to remove it, otherwise it will be a big mess. I haven't run the engine yet to see if the noise level is reduced, but hopefully it will lower it.

My 2000 Toyota Camry LE's OEM Hood heat shield insulation/deadener started deteriorating and pieces of it being peeled off so i decided for a DIY replacement project and bought this Abahub 236mil 4x6 (16sqft - measured first the size of my OEM Hood heat shield as there comes options in sizes). The package came at a very good condition nicely packed inside a plastic and rolled. I inspected the product as there were some reviews about damage/ripped aluminum foil and I am glad mine came in without a damage.Carefully unroll the sheet on a flat surface ( i used my garage floor) and gently flatten the surface (aluminum side facing the ground to prevent damage) and once evenly flat, flip the sheet aluminum now facing up and let it rest and prep for cutting to size matching the OEM from the car. I used sharpie pen to mark the holes and exact size to cut and I just used a medium size office scissor (very easy cut) don't use box cutter it would create a tear to the insulation padding and rip off the aluminum if dragged. There were 11 spots i marked for the location of the round push in clips (when i removed the 11 clips all of them broke and no longer usable but i always keep many clip parts for my vehicles). I was only able to get 4 out of 11 push clips to match the holes when i applied the insulation to the hood (not to worry, the backing adhesive will do the job to hold it together. OEM does not have backing adhesive, it was hold in place by the 11 push clips to the hood)I started from the top which matches the exact location of the top 3 holes allowing me to work without an extra pair of hands. I didn't push the new round clips just halfway and enough to hold the insulation sheet allowing me to access and gently peel off the backing adhesive cover to expose the adhesive part of the sheet. Worked my way from top slowly applying pressure to stick to the hood back surface and making sure the insulation sticks to the surface making sure there is no gap/air.Tip: if during the install, you accidentally damage or rip off a part of the aluminum heat shield, you can simply patch it with an industrial grade aluminum tape (commonly used in HVAC install/repairs).Ultimately, this product can be to cut to size, easy to install with enough thickness and insulation for heat and reducing engine sound/noise when driving the vehicle.I highly recommend, this product won't disappoint you.